...
Product Marketing Name | USB Connect 4G - XXNF | ||
|---|---|---|---|
Revision | 20-004-1.3-XX | Product Variants | XX = EU, NF or AP |
Manufacturer | exelonix GmbH Washingtonstraße 16/16a 01139 Dresden Germany |
Description
...
The USB Connect 4G - XX NF is a USB-Device for cellular communication and supports the LTE CAT 4 standard
...
Electrical Characteristics
...
Mode | Value |
|---|---|
Switched OFF | 25 µA |
Idle Mode (No Call) | max. 15 mA |
Operating Mode | 200 - 600 mA |
USB Voltage Range | 4,8 V - 5,5 V (normally 5 V) |
Getting started with USB Connect 4G -
...
NF
Preparations & Power Up
Install the drivers for Windows/Linux operating system on your host device→ https://www.telit.com/evkevb-drivers/
Plug the USB Connect 4G into the USB Type A socket of the host device.
Make sure that the distance from your body to the USB Connect 4G is greater than 20 cm.
If the USB socket of the host device is active, the USB Connect 4G starts automatically.
Now you can identify the COM port of the USB Connect 4G - XX NF and send AT commands to unlock the at command interface. Therefore you need to send (ask manufacturer for password):
Code Block AT#SECIFAUTH=XXXXXXXXXX
...
To ensure compliance with RF exposure guidelines the device must be used with a minimum of 20cm 5 mm separation from the body. Failure to observe these instructions could result in your RF exposure exceeding the relevant guideline limits. The requirements for the location and the according limitations to locations with distance of minimum 20cm 5 mm to the user are clearly indicated with the USB device. The device is strictly for industrial use/application and installed in industrial environment. This device is not intended for remote access via LTE. This also includes firmware updates and changes to the radio settings via LTE. If a firmware update is necessary, please contact the manufacturer.
...
USB Connect 4G - NF
ISED Certification
...
IC: 5131A25377-LE910CxNFUC4GNF
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The product is in compliance with the SAR requirements. The minimum distance to the body is 5 mm.
FCC Certification
FCC ID: 2AUC4-UC4GNF
This device contains will be registered with the Federal Communications Commission under the following number:
Contains FCC ID: RI7LE910CXNF
...
complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
...
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
...
in a
...
residential installation. This equipment generates, uses
...
and can radiate radio frequency energy and, if not installed and used in accordance with the
...
instructions, may cause harmful interference to radio communications.
...
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications made to the device not expressly approved by the party responsible for compliance may void the user’s authority to operate the equipment.
PTCRB
The product manufactured by Exelonix GmbH is in compliance with PTCRB.
...
The frequency bands and transmitting power (radiated and/or conducted) nominal limits applicable to this radio equipment are as follows:
12, 34, 7, 8, 20, 28A12,66: 23 dBm.
Software Information
...