| Table of Contents | ||
|---|---|---|
|
General Information
Product Marketing Name | USB Connect 4G - EU |
|---|---|
Revision | 20-004-1.3-EU |
Manufacturer | exelonix GmbH Washingtonstraße 16/16a 01139 Dresden Germany |
Description
...
The USB Connect 4G - EU is a USB device for cellular communication and supports the LTE CAT 4 standard.
The device is connected to the host device by a USB Type A interface, which supplies the USB device with power and transmit/receive data.
Supported LTE Bands
LTE Band | Max. Output Power (dBm) | Frequency (MHz) | Uplink (MHz) | Downlink (MHz) | Channels |
|---|---|---|---|---|---|
1 | 23 dBm | 2100 | 1920 – 1980 | 2110 – 2170 | Tx: 18000 - 18599 |
3 | 23 dBm | 1800 | 1710-1785 | 1805-1880 | Tx: 19200 - 19949 |
7 | 23 dBm | 2600 | 2500 – 2570 | 2620 – 2690 | Tx: 20750 - 21449 |
8 | 23 dBm | 900 | 880-915 | 925-960 | Tx: 21450 - 21799 |
20 | 23 dBm | 800 | 832-862 | 791-821 | Tx: 24150 - 24449 |
28A | 23 dBm | 700 | 703-733 | 758-788 | Tx: 27210 - 27510 |
Working und Storage Conditions
Parameter | Minimum Value | Maximum Value | Unit |
|---|---|---|---|
Operating temperature | -20 | +55 | °C |
Storage temperature | -20 | +70 | °C |
Humidity Range | 5 | 95 | % |
Electrical Characteristics
Mode | Value |
|---|---|
Switched OFF | 25 µA |
Idle Mode (No Call) | max. 15 mA |
Operating Mode | 200 - 600 mA |
USB Voltage Range | 4,8 V - 5,5 V (normally 5 V) |
Getting started with USB Connect 4G - EU
Preparations & Power Up
Install the drivers for Windows/Linux operating system on your host device.→ https://www.telit.com/evkevb-drivers/
Plug in the USB Connect 4G into the USB Type A socket of the host device.
Make sure that the distance from your body to the USB Connect 4G is larger than 20 cm.
If the USB socket of the host device is active, the USB Connect 4G starts automatically.
Now you can identify the COM port of the USB Connect 4G - EU and send AT commands to unlock the AT command interface. For this, you need to send the following command (ask manufacturer for password):
Code Block AT#SECIFAUTH=XXXXXXXXXX
Power Down
| Note |
|---|
To avoid any damage to the USB device , the power supply must not be interrupted before the shutdown procedure has been fully carried out. |
First set the following setting via the AT command interface (e.g. via the AT controller):
Code Block AT#GPIO=10,1,1Now the command
Code Block AT#SHDNcan be sent to shut down the USB Connect 4G.
After 15 sec you can safely disconnect the USB Connect 4G from the host device.
Operating
AT commands can be used during operation to establish a network connection. Please find an overview in the AT commands reference guide from Telit: https://www.telit.com/m2m-iot-products/cellular-modules/standard-industrial-grade/xe910-family/#LE910Cx-downloads
...
Hereby, exelonix GmbH declares that the radio equipment type USB Connect 4G - EU is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.exelonix.com/de/
WEEE
Exelonix GmbH fully endorses the environmental objectives of the WEEE. All electronic products must be collected and sent to approved operators for safe disposal of electronic equipment.
...